Low-melting copolyester hot melt for automotive diesel filters. Melting point 154 °C, 37 Pa·s at 190 °C, elongation above 500%. Extruder, melter or spray.
Technipol 157 is a copolyester hot-melt adhesive with a melting point of 154 °C and elongation at break above 500%, designed by Sipol for the production of diesel filters in the automotive industry. Sipol credits it with high chemical resistance to mineral oil and diesel vapors and good thermal resistance.
It is the low-melting grade in Sipol's copolyester filter range. Brookfield viscosity is 37 Pa·s at 190 °C and the melt flow index 41 g/10 min at 190 °C under 0.325 kg, both measured 20 °C lower than the 210 °C used for the other copolyester filter grades.
That low viscosity gives the line a choice of equipment. The data sheet carries both an extruder profile and a melter profile, and Sipol's filter literature adds that Technipol 157 can also be sprayed.
Sipol describes the diesel filter job as keeping wound-up paper in place with chemical resistance to different diesel formulations, through ageing at 90 °C for 168 hours, diesel pressure and vibration. Sipol lists the grade as suitable for all kinds of filter paper.
It is also written as copolyester hot melt adhesive, co-polyester hot melt, polyester hot melt adhesive, thermoplastic copolyester adhesive, and CoPES.
| Property | Typical value |
|---|---|
| Density | 1.25 g/cm³ (ISO 1183) |
| Melting temperature | 154 °C (ISO 11357-3) |
| Elongation at break | Above 500% (ISO 527) |
| Brookfield viscosity | 37 Pa·s at 190 °C (Brookfield CAP 2000+ cone/plate, Sipol method MI 12) |
| MFI | 41 g/10 min at 190 °C, 0.325 kg (ISO 1133) |
| Application method | Extruder, tank melter or spray |
| Form | Granules |
Typical values from the manufacturer's technical data sheet. They describe the product, they are not a specification. We will send the current TDS and the batch documentation your qualification needs.
Tell us the part or the process, the property you are targeting, and the volume you expect. We will confirm the grade, send the documentation, and get a sample of the candidate grade to you.
The use Sipol designed the grade for, holding wound filter paper against diesel and its vapors.
Sipol's filter literature describes the job as keeping wound-up paper in place.
Sipol states its low viscosity allows Technipol 157 to be sprayed.
The data sheet gives a melter profile with a 180 to 190 °C tank.
For extrusion, Sipol suggests 50 to 60 °C under the hopper, 60 to 100 °C in the feeding zone, 120 to 160 °C in the compression zone, and 170 to 180 °C in the metering zone, at the extrusion die or hose and at the nozzle.
For melters, Sipol suggests a pre-heating grid at 165 to 175 °C, the tank at 180 to 190 °C, and the hose and nozzle at 190 to 200 °C.
Material stored at around 5 to 10 °C or below should be held at 15 to 20 °C for at least 24 hours before use.
Package sizes: 25 kg bags with an aluminum film barrier against moisture, 500 kg cardboard octabins with an inner PE liner, and 500 kg and 1000 kg big bags..
Storage: Stable for 12 months unopened in the original packaging, kept in a cool, dry place and protected from light. Material stored at around 5 to 10 °C or below should be held at 15 to 20 °C for at least 24 hours before use.
Read the safety data sheet before handling.
Technipol 157 melts at 154 °C. On an extruder Sipol suggests 170 to 180 °C from the metering zone through the die and nozzle, with the feeding zone at 60 to 100 °C. On a melter Sipol suggests the tank at 180 to 190 °C and the hose and nozzle at 190 to 200 °C. Brookfield viscosity is 37 Pa·s at 190 °C, and its extruder profile tops out 30 to 40 °C below Technipol 170/G's and 60 to 80 °C below Technipol 32's.
Yes, according to Sipol's filter literature. It describes Technipol 157 as a low-melting grade whose low viscosity lets it go through an extruder or a tank unit, and also be sprayed. The data sheet gives the extruder and melter temperature profiles, 170 to 180 °C at the extruder nozzle and 190 to 200 °C at the melter nozzle. Set spray parameters on the line trial with the equipment maker.
Both are Sipol copolyester filter hot melts rated for high resistance to mineral oil and diesel vapors. Technipol 157 melts at 154 °C and is designed for diesel filters; Technipol 170/G melts at 170 °C and is designed for oil and diesel filters. Their melter tanks run at 180 to 190 °C and 210 to 220 °C. Choose 157 where the line or the media favors the lower temperature.
Sipol's filter literature lists the diesel filter requirements its Technipol 157 is aimed at. The bond keeps wound-up paper in place, resists different diesel formulations, holds through ageing at 90 °C for 168 hours, and withstands diesel pressure and vibration. Technipol 157's data sheet rates its chemical resistance to mineral oil and diesel vapors as high. Run the element through its own qualification tests before release.
Yes. We send the Technical Data Sheet (TDS), Safety Data Sheet (SDS), and IMDS data on request, in the manufacturer's current revision. Use Request TDS or SDS above and tell us what your qualification review needs.
Oil and diesel filter grade melting at 170 °C, with extruder and melter profiles.
Very flexible air and oil filter grade at 185 °C, applied by extruder.
Air and oil filter grade with a Vicat point of 140 °C.
The full Technipol range, by chemistry and application.
Copolyester and copolyamide grades for air, oil and diesel filters.
How service temperature, medium and application method pick the grade.