e-Technipol PA 3188

Low-viscosity copolyamide hot melt for electronics, 188 °C softening point and 2.1 Pa·s at 210 °C, with UL94 V0 on its data sheet. For low pressure molding and potting.

Home › Products › Sipol › e-Technipol PA 3188

e-Technipol PA 3188 is an amber copolyamide hot-melt adhesive with a softening point of 188 °C and a low Brookfield viscosity of 2.1 Pa·s at 210 °C. Sipol developed it for the electrical and electronics sector, and credits its low viscosity for its use in melters, low pressure molding, potting and overmolding.

It pairs one of the highest softening points of the e-Technipol PA range with the second-lowest viscosity of the six grades listed here, after PA 3168 at 0.7 Pa·s. The Vicat softening temperature is 59 °C (ISO 306, 1 N), hardness Shore D 35, flexural modulus 40 MPa and elongation at break 175 percent. Low-temperature flexibility is minus 20 °C by ASTM D3111.

Electrical values are a surface resistivity of 2.21 × 10¹² Ω, a volume resistivity of 4.81 × 10¹⁰ Ω·cm, a relative permittivity of 4.43, a dissipation factor of 0.0507 and a comparative tracking index above 600 V. The data sheet reports UL94 V0.

e-Technipol PA 3188 B is the black version, with identical typical values on its own data sheet, and other colors are available on request. Both contain more than 70 percent raw materials from non-edible renewable resources.

It is also written as copolyamide hot melt adhesive, co-polyamide hot melt, polyamide hot melt adhesive, polyamide low pressure molding material, thermoplastic polyamide adhesive, and CoPA.

Typical properties

PropertyTypical value
Softening point188 °C (Sipol method MI 13)
Vicat softening temperature59 °C (ISO 306, 1 N, 50 °C/h)
Low-temperature flexibility-20 °C (ASTM D3111)
Linear thermal expansion, lengthwise237 ppm/K, 23 to 120 °C (ISO 11359)
Linear thermal expansion, crosswise243 ppm/K, 23 to 120 °C (ISO 11359)
Thermal conductivity0.191 W/(m·K) (ASTM E1461)
Brookfield viscosity2.1 Pa·s at 210 °C (Sipol method MI 12, Brookfield CAP 2000+ cone and plate)
Shore D hardness35 instantaneous, 29 after 15 s (ISO 868)
Elongation at break175 percent (ISO 527)
Stress at break6 MPa (ISO 527)
Flexural modulus40 MPa (ISO 178)
Surface resistivity2.21 × 10¹² Ω at 23 °C (IEC 62631-3-1:2016)
Volume resistivity4.81 × 10¹⁰ Ω·cm at 23 °C (IEC 62631-3-1:2016)
Relative permittivity4.43 (ASTM D150:2018)
Dielectric dissipation factor (tan δ)0.0507 (ASTM D150:2018)
Comparative tracking index (CTI)Above 600 V (ASTM D3638:2012)
Density0.98 g/cm³ (ISO 1183)
Water absorption0.96 percent, 23 °C, 24 h immersion (Sipol method MI 08)
Skin time resistance at 210 °Cmore than 4 h
FlammabilityUL94 V0 (IEC 60695-11-10, -20)
Renewable raw materialsMore than 70 percent, from non-edible renewable resources (Sipol data sheet)
ColorAmber; black as e-Technipol PA 3188 B; other colors on request
FormGranules
Versionse-Technipol PA 3188 (amber), e-Technipol PA 3188 B (black), identical typical values

Typical values from the manufacturer's technical data sheet. They describe the product, they are not a specification. We will send the current TDS and the batch documentation your qualification needs.

Need this in your system?

Tell us the part or the process, the property you are targeting, and the volume you expect. We will confirm the grade, send the documentation, and get a sample of the candidate grade to you.

Applications

Low pressure molding

Sipol lists low pressure molding for PA 3188, at 2.1 Pa·s at 210 °C.

Potting

Named on the data sheet among the processes PA 3188 can be used in.

Overmolding

Sipol lists overmolding for PA 3188 alongside low pressure molding.

Melter application

Melter profile from 180 to 210 °C at the pre-heating grid to 195 to 220 °C at the nozzle.

Bonding to metals

Sipol lists excellent adhesion to metals.

PVC and PC substrates

Excellent adhesion to polar plastic substrates, with PVC and PC named.

Handling and dispersion

Sipol's suggested melter profile: pre-heating grid 180 to 210 °C, tank 190 to 210 °C, hose 195 to 220 °C, nozzle 195 to 220 °C.

Sipol's processing data cover melters only. Settings for low pressure molding, potting and overmolding depend on the mold and the machine, and are set in trials.

Sipol rates skin time resistance at 210 °C at more than 4 hours.

Packaging, storage, and regulatory status

Package sizes: 20 kg bags with an aluminum film moisture barrier, 500 kg cardboard octabins with an inner PE liner, and 500 kg big bags..

Storage: Stable for 24 months unopened in the original packaging, kept in a cool, dry place and protected from light. Material held at around 5 to 10 °C or below should stand at 15 to 20 °C for at least 24 hours before use.

Sipol describes e-Technipol PA 3188 as solvent-free and non-toxic, and reports UL94 V0 (IEC 60695-11-10, -20) on the data sheet. Read the safety data sheet before handling.

Frequently asked questions

Can e-Technipol PA 3188 be used for low pressure molding?

Yes. Sipol states that the low viscosity of e-Technipol PA 3188, 2.1 Pa·s at 210 °C, lets it be used in melters and in low pressure molding, potting and overmolding. The melter profile runs 180 to 210 °C at the pre-heating grid, 190 to 210 °C in the tank and 195 to 220 °C at the hose and nozzle. Mold and machine settings are set in trials.

How does e-Technipol PA 3188 compare with e-Technipol PA 3186?

Both soften high, e-Technipol PA 3188 at 188 °C and e-Technipol PA 3186 at 186 °C, and both report UL94 V0. PA 3188 flows more easily, 2.1 Pa·s at 210 °C against 4.5 Pa·s at 225 °C. PA 3186 is the stronger, more extensible solid, with 10 MPa stress at break against 6, 500 percent elongation against 175, a 70 °C Vicat against 59, and flexibility to minus 35 °C against minus 20.

Is e-Technipol PA 3188 UL94 rated?

Yes. The e-Technipol PA 3188 data sheet reports UL94 V0, tested to IEC 60695-11-10 and -20, and the black version, PA 3188 B, reports the same. The sheet does not state the specimen thickness, which a UL94 rating depends on, so ask for the test basis when the rating goes into a product approval. The grade also carries a comparative tracking index above 600 V.

Can I get the TDS and SDS for e-Technipol PA 3188?

Yes. We send the Technical Data Sheet (TDS) and Safety Data Sheet (SDS) on request, in the manufacturer's current revision. Use Request TDS or SDS above and tell us what your qualification review needs.

Related products

e-Technipol PA 3186

Higher Vicat and elongation at a 186 °C softening point, UL94 V0.

e-Technipol PA 3168

Most fluid grade of the range, 0.7 Pa·s at 205 °C.

e-Technipol PA 3192

192 °C softening point and flexible to minus 45 °C.

Where this grade fits

Copolyester and copolyamide hot melts

The Technipol and Technipol PA range by softening point and use.

Electronics hot-melt adhesives

Low pressure molding, potting and overmolding, and how the e-Technipol PA grades compare.

Evaluating e-Technipol PA 3188?

Tell us the system you are formulating and the property you need to hit. We will confirm the grade, send the data sheet, and ship a sample.