Flexible copolyamide hot melt for electronics, 170 °C softening point, 3.4 Pa·s at 210 °C, 30 MPa flexural modulus and 350 percent elongation, flexible to minus 40 °C.
e-Technipol PA 3170 is an amber copolyamide hot-melt adhesive with a softening point of 170 °C, a Brookfield viscosity of 3.4 Pa·s at 210 °C and a flexural modulus of 30 MPa. Sipol developed it for the electrical and electronics sector, for melters, low pressure molding, potting and overmolding.
Sipol characterizes it by a high softening point, a low flexural modulus and a high elongation at break, 350 percent. The 30 MPa modulus is the lowest of the six e-Technipol PA grades listed here. Hardness is Shore D 33, falling to 25 after 15 s, and low-temperature flexibility reaches minus 40 °C by ASTM D3111.
The Vicat softening temperature is 40 °C (ISO 306, 1 N), well below the 170 °C softening point. Compare the upper service temperature of a molded part with the Vicat figure as well.
Electrical values are a surface resistivity of 1.09 × 10¹² Ω, a volume resistivity of 2.70 × 10¹⁰ Ω·cm, a relative permittivity of 4.47, a dissipation factor of 0.0522 and a comparative tracking index above 600 V. The data sheet gives no UL94 rating for this grade.
e-Technipol PA 3170 B is the black version, with identical typical values on its own data sheet, and other colors are available on request. Both contain more than 69 percent raw materials from non-edible renewable resources.
It is also written as copolyamide hot melt adhesive, co-polyamide hot melt, polyamide hot melt adhesive, polyamide low pressure molding material, thermoplastic polyamide adhesive, and CoPA.
| Property | Typical value |
|---|---|
| Softening point | 170 °C (Sipol method MI 13) |
| Vicat softening temperature | 40 °C (ISO 306, 1 N, 50 °C/h) |
| Low-temperature flexibility | -40 °C (ASTM D3111) |
| Linear thermal expansion, lengthwise | 245 ppm/K, 23 to 120 °C (ISO 11359) |
| Linear thermal expansion, crosswise | 309 ppm/K, 23 to 120 °C (ISO 11359) |
| Thermal conductivity | 0.151 W/(m·K) (ASTM E1461) |
| Brookfield viscosity | 3.4 Pa·s at 210 °C (Sipol method MI 12, Brookfield CAP 2000+ cone and plate) |
| Shore D hardness | 33 instantaneous, 25 after 15 s (ISO 868) |
| Elongation at break | 350 percent (ISO 527) |
| Stress at break | 4.5 MPa (ISO 527) |
| Flexural modulus | 30 MPa (ISO 178) |
| Surface resistivity | 1.09 × 10¹² Ω at 23 °C (IEC 62631-3-1:2016) |
| Volume resistivity | 2.70 × 10¹⁰ Ω·cm at 23 °C (IEC 62631-3-1:2016) |
| Relative permittivity | 4.47 (ASTM D150:2018) |
| Dielectric dissipation factor (tan δ) | 0.0522 (ASTM D150:2018) |
| Comparative tracking index (CTI) | Above 600 V (ASTM D3638:2012) |
| Density | 0.98 g/cm³ (ISO 1183) |
| Water absorption | 1.12 percent, 23 °C, 24 h immersion (Sipol method MI 08) |
| Skin time resistance at 210 °C | more than 4 h |
| Renewable raw materials | More than 69 percent, from non-edible renewable resources (Sipol data sheet) |
| Color | Amber; black as e-Technipol PA 3170 B; other colors on request |
| Form | Granules |
| Versions | e-Technipol PA 3170 (amber), e-Technipol PA 3170 B (black), identical typical values |
Typical values from the manufacturer's technical data sheet. They describe the product, they are not a specification. We will send the current TDS and the batch documentation your qualification needs.
Tell us the part or the process, the property you are targeting, and the volume you expect. We will confirm the grade, send the documentation, and get a sample of the candidate grade to you.
Sipol lists low pressure molding for PA 3170, at 3.4 Pa·s at 210 °C.
Named on the data sheet among the processes PA 3170 can be used in.
Sipol lists overmolding for PA 3170 alongside low pressure molding.
Melter profile from 170 to 200 °C at the pre-heating grid to 185 to 210 °C at the nozzle.
Sipol lists excellent adhesion to metals.
Excellent adhesion to polar plastic substrates, with PVC and PC named.
Sipol's suggested melter profile: pre-heating grid 170 to 200 °C, tank 180 to 200 °C, hose 185 to 210 °C, nozzle 185 to 210 °C.
Sipol's processing data cover melters only. Settings for low pressure molding, potting and overmolding depend on the mold and the machine, and are set in trials.
Sipol rates skin time resistance at 210 °C at more than 4 hours.
Package sizes: 20 kg bags with an aluminum film moisture barrier, 500 kg cardboard octabins with an inner PE liner, and 500 kg big bags..
Storage: Stable for 24 months unopened in the original packaging, kept in a cool, dry place and protected from light. Material held at around 5 to 10 °C or below should stand at 15 to 20 °C for at least 24 hours before use.
Sipol describes e-Technipol PA 3170 as solvent-free and non-toxic. Read the safety data sheet before handling.
Yes. Sipol states that e-Technipol PA 3170 can be used in melters and in low pressure molding, potting and overmolding. It softens at 170 °C and measures 3.4 Pa·s at 210 °C. The melter profile runs 170 to 200 °C at the pre-heating grid, 180 to 200 °C in the tank and 185 to 210 °C at the hose and nozzle. Mold and machine settings are set in trials.
The e-Technipol PA 3170 data sheet carries no UL94 rating. Where V0 is required, e-Technipol PA 3168, PA 3186, PA 3188 and PA 3192 each report UL94 V0 on their data sheets. PA 3170 does carry the full electrical table, with a comparative tracking index above 600 V, a volume resistivity of 2.70 × 10¹⁰ Ω·cm and a relative permittivity of 4.47.
e-Technipol PA 3170 softens at 170 °C and is Shore D 33; e-Technipol PA 3162 softens at 162 °C and is Shore D 25. Both have a 40 °C Vicat temperature and the same melter profile. PA 3170 gives more elongation, 350 percent against 250, and lower water absorption, 1.12 percent against 1.77. PA 3162 stays flexible to minus 50 °C against minus 40 °C.
The data sheets give e-Technipol PA 3170 and Technipol PA 2170 the same 170 °C softening point, 3.4 Pa·s at 210 °C, Shore D 33 and 30 MPa flexural modulus. PA 3170 lists 350 percent elongation against 600 percent for PA 2170. e-Technipol PA 3170 is the grade developed for electrical and electronics work, with the electrical, thermal and water-absorption data to support it.
Yes. We send the Technical Data Sheet (TDS) and Safety Data Sheet (SDS) on request, in the manufacturer's current revision. Use Request TDS or SDS above and tell us what your qualification review needs.
Softer at Shore D 25, flexible to minus 50 °C.
192 °C softening point, flexible to minus 45 °C, UL94 V0.
Same softening point and viscosity, general-purpose with 600 percent elongation.
The Technipol and Technipol PA range by softening point and use.
Low pressure molding, potting and overmolding, and how the e-Technipol PA grades compare.