e-Technipol PA 3168

Very low viscosity copolyamide for electronics potting, 0.7 Pa·s at 205 °C, 168 °C softening point, 70 MPa flexural modulus and UL94 V0 on its data sheet.

Home › Products › Sipol › e-Technipol PA 3168

e-Technipol PA 3168 is an amber copolyamide hot-melt adhesive with a very low Brookfield viscosity of 0.7 Pa·s at 205 °C, a softening point of 168 °C and a flexural modulus of 70 MPa. Sipol developed it for the electrical and electronics sector and names potting first among its processes, then melters, low pressure molding and overmolding.

At 0.7 Pa·s it is the most fluid of the six e-Technipol PA grades listed here, which run 2.1 to 4.5 Pa·s. Sipol ties its use in potting to that low viscosity. The mechanical table shows the other side: the highest flexural modulus of the range, Shore D 37, and the lowest elongation at break, 100 percent.

Low-temperature flexibility is minus 5 °C by ASTM D3111, against minus 20 to minus 50 °C for the other grades. The Vicat softening temperature is 50 °C (ISO 306, 1 N).

Electrical values are a surface resistivity of 2.23 × 10¹² Ω, a volume resistivity of 6.25 × 10¹⁰ Ω·cm, a relative permittivity of 6.42, a dissipation factor of 0.1689 and a comparative tracking index above 600 V. The data sheet reports UL94 V0. Water absorption is 0.49 percent after 24 h immersion, the lowest of the six.

e-Technipol PA 3168 B is the black version, with identical typical values on its own data sheet, and other colors are available on request. Both contain more than 74 percent raw materials from non-edible renewable resources.

It is also written as copolyamide hot melt adhesive, co-polyamide hot melt, polyamide hot melt adhesive, polyamide low pressure molding material, thermoplastic polyamide adhesive, and CoPA.

Typical properties

PropertyTypical value
Softening point168 °C (Sipol method MI 13)
Vicat softening temperature50 °C (ISO 306, 1 N, 50 °C/h)
Low-temperature flexibility-5 °C (ASTM D3111)
Linear thermal expansion, lengthwise185 ppm/K, 23 to 120 °C (ISO 11359)
Linear thermal expansion, crosswise321 ppm/K, 23 to 120 °C (ISO 11359)
Thermal conductivity0.208 W/(m·K) (ASTM E1461)
Brookfield viscosity0.7 Pa·s at 205 °C (Sipol method MI 12, Brookfield CAP 2000+ cone and plate)
Shore D hardness37 instantaneous, 33 after 15 s (ISO 868)
Elongation at break100 percent (ISO 527)
Stress at break6 MPa (ISO 527)
Flexural modulus70 MPa (ISO 178)
Surface resistivity2.23 × 10¹² Ω at 23 °C (IEC 62631-3-1:2016)
Volume resistivity6.25 × 10¹⁰ Ω·cm at 23 °C (IEC 62631-3-1:2016)
Relative permittivity6.42 (ASTM D150:2018)
Dielectric dissipation factor (tan δ)0.1689 (ASTM D150:2018)
Comparative tracking index (CTI)Above 600 V (ASTM D3638:2012)
Density0.97 g/cm³ (ISO 1183)
Water absorption0.49 percent, 23 °C, 24 h immersion (Sipol method MI 08)
Skin time resistance at 210 °Cmore than 3 h
FlammabilityUL94 V0 (IEC 60695-11-10, -20)
Renewable raw materialsMore than 74 percent, from non-edible renewable resources (Sipol data sheet)
ColorAmber; black as e-Technipol PA 3168 B; other colors on request
FormGranules
Versionse-Technipol PA 3168 (amber), e-Technipol PA 3168 B (black), identical typical values

Typical values from the manufacturer's technical data sheet. They describe the product, they are not a specification. We will send the current TDS and the batch documentation your qualification needs.

Need this in your system?

Tell us the part or the process, the property you are targeting, and the volume you expect. We will confirm the grade, send the documentation, and get a sample of the candidate grade to you.

Applications

Potting

Named on the data sheet among the processes PA 3168 can be used in.

Low pressure molding

Sipol lists low pressure molding for PA 3168, at 0.7 Pa·s at 205 °C.

Overmolding

Sipol lists overmolding for PA 3168 alongside low pressure molding.

Melter application

Melter profile from 170 to 200 °C at the pre-heating grid to 185 to 210 °C at the nozzle.

Bonding to metals

Sipol lists excellent adhesion to metals.

PVC and PC substrates

Excellent adhesion to polar plastic substrates, with PVC and PC named.

Handling and dispersion

Sipol's suggested melter profile: pre-heating grid 170 to 200 °C, tank 180 to 200 °C, hose 185 to 210 °C, nozzle 185 to 210 °C.

Sipol's processing data cover melters only. Settings for low pressure molding, potting and overmolding depend on the mold and the machine, and are set in trials.

Sipol rates skin time resistance at 210 °C at more than 3 hours.

Packaging, storage, and regulatory status

Package sizes: 20 kg bags with an aluminum film moisture barrier, 500 kg cardboard octabins with an inner PE liner, and 500 kg big bags..

Storage: Stable for 24 months unopened in the original packaging, kept in a cool, dry place and protected from light. Material held at around 5 to 10 °C or below should stand at 15 to 20 °C for at least 24 hours before use.

Sipol describes e-Technipol PA 3168 as solvent-free and non-toxic, and reports UL94 V0 (IEC 60695-11-10, -20) on the data sheet. Read the safety data sheet before handling.

Frequently asked questions

Why use e-Technipol PA 3168 for potting?

Sipol names potting first for e-Technipol PA 3168 because of its very low viscosity, 0.7 Pa·s at 205 °C. The other e-Technipol PA grades listed here measure 2.1 to 4.5 Pa·s. A thinner melt fills a housing and flows around components at lower pressure. The grade also reports UL94 V0 and a comparative tracking index above 600 V on its data sheet.

What are the limits of e-Technipol PA 3168?

e-Technipol PA 3168 is the stiffest and least extensible grade of the e-Technipol PA range listed here, with a 70 MPa flexural modulus, Shore D 37 and 100 percent elongation at break. Low-temperature flexibility is minus 5 °C by ASTM D3111, against minus 20 to minus 50 °C for the other grades. Where a part sees deep cold or has to flex, look at e-Technipol PA 3192 or PA 3162.

Is e-Technipol PA 3168 UL94 rated?

Yes. The e-Technipol PA 3168 data sheet reports UL94 V0, tested to IEC 60695-11-10 and -20, and the black version, PA 3168 B, reports the same. The sheet does not state the specimen thickness, which a UL94 rating depends on, so ask for the test basis when the rating goes into a product approval. The grade also carries a comparative tracking index above 600 V.

How does e-Technipol PA 3168 compare with e-Technipol PA 3188?

e-Technipol PA 3188 is the next most fluid grade, 2.1 Pa·s at 210 °C against 0.7 Pa·s at 205 °C for e-Technipol PA 3168. PA 3188 softens higher, 188 °C against 168 °C, stays flexible to minus 20 °C against minus 5 °C, and gives 175 percent elongation against 100. Both report UL94 V0 and a comparative tracking index above 600 V.

Can I get the TDS and SDS for e-Technipol PA 3168?

Yes. We send the Technical Data Sheet (TDS) and Safety Data Sheet (SDS) on request, in the manufacturer's current revision. Use Request TDS or SDS above and tell us what your qualification review needs.

Related products

e-Technipol PA 3188

Next most fluid grade, 2.1 Pa·s at 210 °C, with a 188 °C softening point.

e-Technipol PA 3186

Highest Vicat and elongation of the range, UL94 V0.

e-Technipol PA 3162

Soft, low-temperature grade flexible to minus 50 °C.

Where this grade fits

Copolyester and copolyamide hot melts

The Technipol and Technipol PA range by softening point and use.

Electronics hot-melt adhesives

Low pressure molding, potting and overmolding, and how the e-Technipol PA grades compare.

Evaluating e-Technipol PA 3168?

Tell us the system you are formulating and the property you need to hit. We will confirm the grade, send the data sheet, and ship a sample.