e-Technipol PA 3192

Copolyamide hot melt for electronics, 192 °C softening point, 3.1 Pa·s at 210 °C, flexible to minus 45 °C, with UL94 V0 on its data sheet.

Home › Products › Sipol › e-Technipol PA 3192

e-Technipol PA 3192 is an amber copolyamide hot-melt adhesive with a softening point of 192 °C and a Brookfield viscosity of 3.1 Pa·s at 210 °C. Sipol developed it for the electrical and electronics sector, for melters, low pressure molding, potting and overmolding, and gives it a wide range of application temperatures, from minus 55 °C to 150 °C.

Its 192 °C softening point is the highest of the six e-Technipol PA grades listed here, and its low-temperature flexibility of minus 45 °C by ASTM D3111 is second only to PA 3162. Hardness is Shore D 40, flexural modulus 60 MPa, stress at break 6 MPa and elongation at break 400 percent. The Vicat softening temperature is 53 °C (ISO 306, 1 N).

Electrical values are a surface resistivity of 1.00 × 10¹² Ω, a volume resistivity of 3.55 × 10¹⁰ Ω·cm, a relative permittivity of 4.68, a dissipation factor of 0.0607 and a comparative tracking index above 600 V. The data sheet reports UL94 V0.

e-Technipol PA 3192 B is the black version, with identical typical values on its own data sheet, and other colors are available on request. Both contain more than 65 percent raw materials from non-edible renewable resources.

It is also written as copolyamide hot melt adhesive, co-polyamide hot melt, polyamide hot melt adhesive, polyamide low pressure molding material, thermoplastic polyamide adhesive, and CoPA.

Typical properties

PropertyTypical value
Softening point192 °C (Sipol method MI 13)
Vicat softening temperature53 °C (ISO 306, 1 N, 50 °C/h)
Low-temperature flexibility-45 °C (ASTM D3111)
Linear thermal expansion, lengthwise231 ppm/K, 23 to 120 °C (ISO 11359)
Linear thermal expansion, crosswise259 ppm/K, 23 to 120 °C (ISO 11359)
Thermal conductivity0.179 W/(m·K) (ASTM E1461)
Brookfield viscosity3.1 Pa·s at 210 °C (Sipol method MI 12, Brookfield CAP 2000+ cone and plate)
Shore D hardness40 instantaneous, 33 after 15 s (ISO 868)
Elongation at break400 percent (ISO 527)
Stress at break6 MPa (ISO 527)
Flexural modulus60 MPa (ISO 178)
Surface resistivity1.00 × 10¹² Ω at 23 °C (IEC 62631-3-1:2016)
Volume resistivity3.55 × 10¹⁰ Ω·cm at 23 °C (IEC 62631-3-1:2016)
Relative permittivity4.68 (ASTM D150:2018)
Dielectric dissipation factor (tan δ)0.0607 (ASTM D150:2018)
Comparative tracking index (CTI)Above 600 V (ASTM D3638:2012)
Density0.98 g/cm³ (ISO 1183)
Water absorption1.15 percent, 23 °C, 24 h immersion (Sipol method MI 08)
Skin time resistance at 210 °Cmore than 4 h
FlammabilityUL94 V0 (IEC 60695-11-10, -20)
Renewable raw materialsMore than 65 percent, from non-edible renewable resources (Sipol data sheet)
ColorAmber; black as e-Technipol PA 3192 B; other colors on request
FormGranules
Versionse-Technipol PA 3192 (amber), e-Technipol PA 3192 B (black), identical typical values

Typical values from the manufacturer's technical data sheet. They describe the product, they are not a specification. We will send the current TDS and the batch documentation your qualification needs.

Need this in your system?

Tell us the part or the process, the property you are targeting, and the volume you expect. We will confirm the grade, send the documentation, and get a sample of the candidate grade to you.

Applications

Low pressure molding

Sipol lists low pressure molding for PA 3192, at 3.1 Pa·s at 210 °C.

Potting

Named on the data sheet among the processes PA 3192 can be used in.

Overmolding

Sipol lists overmolding for PA 3192 alongside low pressure molding.

Melter application

Melter profile from 180 to 210 °C at the pre-heating grid to 195 to 220 °C at the nozzle.

Bonding to metals

Sipol lists excellent adhesion to metals.

PVC and PC substrates

Excellent adhesion to polar plastic substrates, with PVC and PC named.

Handling and dispersion

Sipol's suggested melter profile: pre-heating grid 180 to 210 °C, tank 190 to 210 °C, hose 195 to 220 °C, nozzle 195 to 220 °C.

Sipol's processing data cover melters only. Settings for low pressure molding, potting and overmolding depend on the mold and the machine, and are set in trials.

Sipol rates skin time resistance at 210 °C at more than 4 hours.

Packaging, storage, and regulatory status

Package sizes: 20 kg bags with an aluminum film moisture barrier, 500 kg cardboard octabins with an inner PE liner, and 500 kg big bags..

Storage: Stable for 24 months unopened in the original packaging, kept in a cool, dry place and protected from light. Material held at around 5 to 10 °C or below should stand at 15 to 20 °C for at least 24 hours before use.

Sipol describes e-Technipol PA 3192 as solvent-free and non-toxic, and reports UL94 V0 (IEC 60695-11-10, -20) on the data sheet. Read the safety data sheet before handling.

Frequently asked questions

What temperature range does e-Technipol PA 3192 cover?

Sipol gives e-Technipol PA 3192 a wide range of application temperatures, from minus 55 °C to 150 °C. The data sheet supports both ends with a 192 °C softening point, a 53 °C Vicat temperature by ISO 306 and low-temperature flexibility of minus 45 °C by ASTM D3111. Ask for the test basis of the 150 °C figure before it goes into a design limit.

Can e-Technipol PA 3192 be used for low pressure molding?

Yes. Sipol states that e-Technipol PA 3192, at 3.1 Pa·s at 210 °C, can be used in melters and in low pressure molding, potting and overmolding. The melter profile runs 180 to 210 °C at the pre-heating grid, 190 to 210 °C in the tank and 195 to 220 °C at the hose and nozzle. Mold and machine settings are set in trials.

Is e-Technipol PA 3192 UL94 rated?

Yes. The e-Technipol PA 3192 data sheet reports UL94 V0, tested to IEC 60695-11-10 and -20, and the black version, PA 3192 B, reports the same. The sheet does not state the specimen thickness, which a UL94 rating depends on, so ask for the test basis when the rating goes into a product approval. The grade also carries a comparative tracking index above 600 V.

How does e-Technipol PA 3192 compare with e-Technipol PA 3186?

e-Technipol PA 3192 softens at 192 °C and stays flexible to minus 45 °C; e-Technipol PA 3186 softens at 186 °C and stays flexible to minus 35 °C. PA 3186 has the higher Vicat temperature, 70 °C against 53, more elongation, 500 percent against 400, and the stronger insulation values. PA 3192 runs at 3.1 Pa·s at 210 °C against 4.5 Pa·s at 225 °C. Both report UL94 V0.

Can I get the TDS and SDS for e-Technipol PA 3192?

Yes. We send the Technical Data Sheet (TDS) and Safety Data Sheet (SDS) on request, in the manufacturer's current revision. Use Request TDS or SDS above and tell us what your qualification review needs.

Related products

e-Technipol PA 3186

Highest Vicat and elongation of the range, UL94 V0.

e-Technipol PA 3162

Flexible to minus 50 °C, the softest grade at Shore D 25.

e-Technipol PA 3188

Lower viscosity, 2.1 Pa·s at 210 °C, at a 188 °C softening point.

Where this grade fits

Copolyester and copolyamide hot melts

The Technipol and Technipol PA range by softening point and use.

Electronics hot-melt adhesives

Low pressure molding, potting and overmolding, and how the e-Technipol PA grades compare.

Evaluating e-Technipol PA 3192?

Tell us the system you are formulating and the property you need to hit. We will confirm the grade, send the data sheet, and ship a sample.