Sipolprene B breathable grades

Five ether ester TPC-ET grades developed for good water vapor breathability, Shore D 40 to 53 and melting at 183 to 218 °C. Injection molding and extrusion.

Home › Products › Sipol › Sipolprene B breathable grades

Sipolprene B is Sipol's breathable family, five ether ester thermoplastic elastomer (TPC-ET) grades from Shore D 40 to Shore D 53, with melting temperatures of 183 to 218 °C. Sipol developed them with good breathability with respect to water vapor, and rates each one for injection molding and extrusion.

The figure that sets these grades apart on the data sheet is water absorption, 20 to 40 percent after 24 hours of immersion at 23 °C. Sipol calls for drying at 70 °C for 4 to 5 hours, a lower temperature and a longer time than the 90 °C for 2 to 4 hours on the standard Sipolprene data sheets. The data sheets give no water vapor transmission rate.

B 4020 is the softest at Shore D 40 and the most absorbent at 40 percent. B 4318 and B 4319 are both Shore D 44, split by melting point, 183 °C against 193 °C, and by elongation, 425 against 500 percent. B 4721 at Shore D 47 and B 5422 at Shore D 53 are the stiff end, at 120 and 130 MPa flexural modulus, with water absorption down to 22 and 20 percent.

All five show no break in notched Izod at 23 °C. At -40 °C, B 4020, B 4318 and B 4319 show no break, B 4721 gives 164 J/m and B 5422 gives 190 J/m.

Each grade comes in a natural color on its own data sheet. None of the five sheets carries a food contact statement.

It is also written as TPC-ET, thermoplastic copolyester elastomer, breathable TPC-ET, breathable copolyester elastomer, TPEE, COPE, copolyester elastomer, and ether ester elastomer.

Typical properties

PropertyTypical value
GradesB 4020, B 4318, B 4319, B 4721, B 5422
Shore D hardness40 to 53 instantaneous across the family (ISO 868)
Melting temperature183 to 218 °C (ISO 11357-3)
Crystallization temperature127 to 175 °C (ISO 11357-3)
Melt flow index (MFI)15 to 30 g/10 min at 230 °C, 2.16 kg (ISO 1133)
Melt volume rate (MVR)12 to 25 cm³/10 min at 230 °C, 2.16 kg (ISO 1133)
Stress at break25 to 36 MPa (ISO 527)
Elongation at break425 to 650 percent (ISO 527)
Flexural modulus60 to 130 MPa (ISO 178)
Notched Izod impact, 23 °CNo break, all five grades (ISO 180)
Notched Izod impact, -40 °CNo break for B 4020, B 4318 and B 4319; 164 J/m for B 4721; 190 J/m for B 5422 (ISO 180)
Abrasion resistance26 to 41 mm³ at 5 N vertical load (ISO 4649)
Density1.20 to 1.22 g/cm³ (ISO 1183)
Water absorption20 to 40 percent, 24 h immersion at 23 °C (Sipol method MI 08)
Water vaporDeveloped for good breathability with respect to water vapor; no transmission rate on the TDS
ColorNatural
Drying70 °C for 4 to 5 h in a dehumidifying dryer, to 0.15 percent moisture

Typical values from the manufacturer's technical data sheet. They describe the product, they are not a specification. We will send the current TDS and the batch documentation your qualification needs.

Need this in your system?

Tell us the part or the process, the property you are targeting, and the volume you expect. We will confirm the grade, send the documentation, and get a sample of the candidate grade to you.

Recommended grades

GradeShore D, instantaneous / 15 sMelting pointMFI, 230 °C, 2.16 kgFlexural modulusWater absorption, 24 h
Sipolprene B 402040 / 37203 °C22 g/10 min60 MPa40 percent
Sipolprene B 431844 / 41183 °C26 g/10 min74 MPa30 percent
Sipolprene B 431944 / 41193 °C30 g/10 min75 MPa30 percent
Sipolprene B 472147 / 45211 °C25 g/10 min120 MPa22 percent
Sipolprene B 542253 / 50218 °C15 g/10 min130 MPa20 percent

Values are the manufacturer's published typical figures. Ask for the current technical data sheet on any grade and we will send it with the matching safety data sheet.

Applications

Water vapor breathable extrusions

Sipol developed the family for good breathability with respect to water vapor and rates every grade for extrusion.

Breathable injection molded parts

Each grade is rated for injection molding, with the mold at 30 to 40 °C.

A choice of stiffness

Flexural modulus runs from 60 MPa for B 4020 to 130 MPa for B 5422.

Handling and dispersion

Dry every grade at 70 °C for 4 to 5 hours in a dehumidifying dryer, to a processing moisture content of 0.15 percent. With water absorption of 20 to 40 percent in 24 hours of immersion, the material picks up moisture quickly once the bag is open.

Suggested injection molding profiles, rear zone to nozzle, with the mold at 30 to 40 °C for all five. B 4020 runs 190, 200, 210 and 215 °C. B 4318 runs 170, 185, 195 and 200 °C. B 4319 runs 180, 190, 200 and 210 °C. B 4721 runs 190, 210, 220 and 220 °C. B 5422 runs 210, 220, 230 and 240 °C.

Suggested extrusion profiles, feeding zone to head or die. B 4020 runs 190 to 205, 205 to 215, 210 to 225 and 210 to 225 °C. B 4318 runs 180 to 190, 190 to 200, 200 to 210 and 200 to 210 °C. B 4319 runs 190 to 200, 200 to 210, 210 to 220 and 210 to 220 °C. B 4721 runs 211 to 220, 220 to 230, 240 to 250 and 240 to 250 °C. B 5422 runs 200 to 215, 215 to 225, 225 to 235 and 235 to 245 °C.

Packaging, storage, and regulatory status

Package sizes: 25 kg bags with an aluminum film moisture barrier, 500 kg cardboard octabins with an inner PE liner, and 500 kg and 1000 kg big bags..

Storage: Stable for 12 months unopened in the original packaging, kept cool and dry and protected from light. Material held at around 5 to 10 °C or below should sit at 15 to 20 °C for at least 24 hours before use.

Read the safety data sheet before handling. The Sipolprene B data sheets carry no food contact statement.

Frequently asked questions

What does breathable mean on the Sipolprene B grades?

Sipol describes the Sipolprene B grades, B 4020 to B 5422, as specially developed with good breathability with respect to water vapor. The data sheets do not give a water vapor transmission rate. What they do show is water absorption of 20 to 40 percent after 24 hours of immersion, far above the 0.5 and 0.4 percent of Sipolprene 46185 and 48200. Tell us the thickness and test method you specify and we will take the question to Sipol.

How should Sipolprene B grades be dried?

All five Sipolprene B data sheets call for drying at 70 °C for 4 to 5 hours in a dehumidifying dryer, to a processing moisture content of 0.15 percent. That is a lower temperature and a longer time than the 90 °C for 2 to 4 hours on the standard Sipolprene grades, and it matches a family that absorbs 20 to 40 percent water in 24 hours of immersion.

What separates Sipolprene B 4318 from B 4319?

Sipolprene B 4318 and B 4319 are both Shore D 44 with 30 percent water absorption. B 4318 melts at 183 °C and processes cooler, with a 200 °C nozzle; B 4319 melts at 193 °C with a 210 °C nozzle. B 4319 stretches further, 500 percent against 425, and flows faster at 30 g/10 min against 26. B 4318 has the lower abrasion loss, 29 mm³ against 41.

Which Sipolprene B grade is the stiffest?

Sipolprene B 5422 is the hardest and stiffest of the five, at Shore D 53 and 130 MPa flexural modulus, with a 218 °C melting point and the lowest water absorption in the family at 20 percent. B 4721 is close behind at Shore D 47 and 120 MPa. At -40 °C the two give 190 and 164 J/m notched Izod, where the softer three show no break.

Can I get the TDS and SDS for Sipolprene B breathable grades?

Yes. We send the Technical Data Sheet (TDS) and Safety Data Sheet (SDS) on request, in the manufacturer's current revision. Use Request TDS or SDS above and tell us what your qualification review needs.

Related products

Sipolprene S grades with renewable content

Experimental grades whose data sheets give a breathability figure by Sipol method MI 18.

Sipolprene 48200

A standard Shore D 48 grade with 0.4 percent water absorption and food contact statements.

Sipolprene 44210

A standard Shore D 46 grade melting at 212 °C, with an HV version for extrusion.

Where this grade fits

TPC-ET copolyester elastomers

The Sipolprene range from soft to hard, and where copolyester elastomer fits against TPU.

What is TPC-ET

What the TPC-ET name means and how the family differs from TPU.

Matching a TPC-ET specification

How to match a copolyester elastomer specification by hardness, melt flow and version.

Evaluating Sipolprene B breathable grades?

Tell us the system you are formulating and the property you need to hit. We will confirm the grade, send the data sheet, and ship a sample.