Sipolprene 55211

TPC-ET at Shore D 54 with a 213 °C melting point, 172 °C crystallization temperature and MFI 12, for injection molding and extrusion.

Home › Products › Sipol › Sipolprene 55211

Sipolprene 55211 is a thermoplastic copolyester elastomer (TPC-ET) at Shore D 54, with a 213 °C melting point and a melt flow of 12 g/10 min at 230 °C, 2.16 kg. Sipol designed it as an ether ester elastomer whose rheology suits injection molding and extrusion.

Its crystallization temperature is 172 °C, 41 degrees below the melt. A higher crystallization temperature generally lets a molded part solidify sooner in a cooled mold, and Sipol's suggested mold temperature for the natural grade is 20 to 30 °C.

Compression set is 33 percent at 23 °C and 46 percent at 70 °C (ISO 815), lower at 70 °C than Sipolprene 54205 at 60 percent or 58210 at 67 percent. Notched Izod is no break at 23 °C and at -40 °C, and the glass transition sits at -18 °C.

Flexural modulus is 150 MPa, stress at break 32 MPa and elongation at break 410 percent. Water absorption is 1.7 percent after 24 hours of immersion, so drying matters: Sipol specifies 3 to 4 hours at 90 °C.

Two versions have their own Sipol data sheets. 55211 B is a black dry blend and 55211 W a UV-stabilized dry blend. Both sheets list 29 MPa stress at break, 480 percent elongation and 60 J/m notched Izod at -40 °C, against 32 MPa, 410 percent and no break for the natural grade. A heat-stabilized dry blend is available on request.

It is also written as TPC-ET, thermoplastic copolyester elastomer, TPEE, TEEE, COPE, copolyester elastomer, thermoplastic polyester elastomer, and ether ester elastomer.

Typical properties

PropertyTypical value
Melting temperature213 °C (ISO 11357-3)
Crystallization temperature172 °C (ISO 11357-3)
Glass transition temperature-18 °C (ISO 11357-2)
Vicat softening temperature A/50183 °C (ISO 306)
Melt flow index (MFI)12 g/10 min at 230 °C, 2.16 kg (ISO 1133)
Melt volume rate (MVR)10 cm³/10 min at 230 °C, 2.16 kg (ISO 1133)
Shore D hardness54 instantaneous, 51 after 15 s (ISO 868)
Stress at break32 MPa (ISO 527)
Elongation at break410 % (ISO 527)
Flexural modulus150 MPa (ISO 178)
Notched Izod impact at 23 °CNo break (ISO 180)
Notched Izod impact at -40 °CNo break (ISO 180)
Abrasion loss36 mm³ at 5 N vertical load (ISO 4649)
Compression set at 23 °C33 % (ISO 815:1991)
Compression set at 70 °C46 % (ISO 815:1991)
Density1.21 g/cm³ (ISO 1183)
Water absorption1.7 % after 24 h immersion at 23 °C (Sipol method MI 08)
FormGranules
Versions55211 B (black dry blend), 55211 W (UV-stabilized dry blend)
55211 B and 55211 WStress at break 29 MPa; elongation at break 480 %; notched Izod 60 J/m at -40 °C; other values as the natural grade

Typical values from the manufacturer's technical data sheet. They describe the product, they are not a specification. We will send the current TDS and the batch documentation your qualification needs.

Need this in your system?

Tell us the part or the process, the property you are targeting, and the volume you expect. We will confirm the grade, send the documentation, and get a sample of the candidate grade to you.

Applications

Injection molded parts

Sipol's profile runs 150 to 165 °C at the rear zone up to 235 °C at the nozzle, with the mold at 20 to 30 °C.

Extruded parts

The extrusion profile climbs from 200 to 215 °C at the feed to 215 to 230 °C at the head and die.

Black parts

55211 B is the black dry blend.

UV-exposed parts

55211 W is the UV-stabilized dry blend.

Handling and dispersion

Dry before processing. Sipol recommends 3 to 4 hours at 90 °C in a dehumidifying dryer and gives a processing moisture content of 0.15 percent. The 55211 B sheet gives 2 to 3 hours.

For injection molding, Sipol suggests the rear zone at 150 to 165 °C, the center zone at 215 °C, the front zone at 225 °C and the nozzle at 235 °C, with the mold at 20 to 30 °C. The 55211 B sheet gives a mold temperature of 30 to 40 °C.

For extrusion, the suggested profile is feed zone 200 to 215 °C, compression zone 210 to 220 °C, metering zone 215 to 230 °C and head or die 215 to 230 °C. The 55211 B sheet gives 200 to 210 °C at the feed and 220 to 225 °C through metering and the die.

Packaging, storage, and regulatory status

Package sizes: 25 kg bags with an aluminum film moisture barrier, 500 kg cardboard octabins with an inner PE liner, and 500 kg or 1000 kg big bags..

Storage: Stable for 12 months unopened in the original packaging, kept in a cool, dry place and protected from light. Material held at around 5 to 10 °C or below should sit at 15 to 20 °C for at least 24 hours before use.

Read the safety data sheet before handling.

Frequently asked questions

What processing temperatures does Sipolprene 55211 need?

Sipolprene 55211 melts at 213 °C. For injection molding Sipol suggests 150 to 165 °C at the rear zone, 215 °C center, 225 °C front and 235 °C at the nozzle, with the mold at 20 to 30 °C. For extrusion the profile runs 200 to 215 °C at the feed, 210 to 220 °C in compression, and 215 to 230 °C through metering and the die. Dry 3 to 4 hours at 90 °C first.

Why does Sipolprene 55211 need longer drying?

Sipolprene 55211 absorbs 1.7 percent water after 24 hours of immersion at 23 °C, against 0.30 to 0.40 percent for Sipolprene 54205 and 55200. Sipol's sheet calls for 3 to 4 hours at 90 °C in a dehumidifying dryer, one hour more than those grades, to reach the 0.15 percent processing moisture content.

What separates Sipolprene 55211 from Sipolprene 55200?

Sipolprene 55211 is Shore D 54 against 53, melts at 213 °C against 198 °C, and crystallizes at 172 °C against 147 °C. Its melt flow is lower, 12 against 20 g/10 min. Compression set at 70 °C is 46 percent against 61 percent. Sipolprene 55200 is stronger in tension, 43 MPa against 32 MPa, and carries an FDA and EU 10/2011 food contact statement that the 55211 sheet does not.

Is Sipolprene 55211 food-contact compliant?

Sipol's data sheets for Sipolprene 55211, 55211 B and 55211 W carry no food contact statement, so we make no food contact claim for this grade. For a food-contact part at a similar Shore D 53 to 54, Sipolprene 55200 and 54205 are both stated by Sipol to be in compliance with American FDA and European EU 10/2011 food contact regulations in their natural versions.

Can I get the TDS and SDS for Sipolprene 55211?

Yes. We send the Technical Data Sheet (TDS) and Safety Data Sheet (SDS) on request, in the manufacturer's current revision. Use Request TDS or SDS above and tell us what your qualification review needs.

Related products

Sipolprene 54205

The same Shore D 54 with a 204 °C melt, MFI 20 and a food contact statement.

Sipolprene 55200

Shore D 53 at MFI 20, natural grade stated FDA and EU 10/2011 compliant.

Sipolprene 58210

Stiffer at Shore D 58, with a 174 °C crystallization temperature.

Where this grade fits

TPC-ET copolyester elastomers

The Sipolprene range by hardness and melting point, and where copolyester elastomer does not fit.

What is TPC-ET

What the TPC-ET name means and how copolyester elastomer differs from TPU.

Matching a TPC-ET specification

Matching an existing specification by Shore D hardness, melt viscosity and version suffix.

Evaluating Sipolprene 55211?

Tell us the system you are formulating and the property you need to hit. We will confirm the grade, send the data sheet, and ship a sample.