Sipolprene 25185

Shore D 29 ether ester TPC-ET melting at 184 °C, with 98 °C Vicat softening and 35 mm³ abrasion loss. Natural grade meets FDA and EU 10/2011.

Home › Products › Sipol › Sipolprene 25185

Sipolprene 25185 is an ether ester thermoplastic elastomer (TPC-ET) at a nominal Shore D 29, with a melting temperature of 184 °C and a Vicat A softening point of 98 °C. Sipol rates its melt behavior as suitable for injection molding and extrusion.

It is soft, with a 35 MPa flexural modulus, 700 percent elongation at break and 25 MPa stress at break. The 98 °C Vicat point is 25 °C above that of Sipolprene 25170, which matters for a soft part that sees heat.

Abrasion loss is 35 mm³ at 5 N, and notched Izod shows no break at 23 °C or -40 °C, with the glass transition at -65 °C. Compression set is 24 percent at 23 °C and 65 percent at 70 °C.

Melt flow is 20 g/10 min measured at 220 °C and 2.16 kg. The extrusion and molding profiles on the data sheet both stay at or below 210 °C.

The natural grade comes with a standard stabilization package and Sipol states it is in compliance with American FDA and European EU 10/2011 food contact regulations. Two dry blend versions have their own data sheets with the same property table: 25185 B in black and 25185 W UV stabilized. Sipol also offers heat-stabilized dry blends on request.

It is also written as TPC-ET, thermoplastic copolyester elastomer, TPEE, TEEE, COPE, copolyester elastomer, thermoplastic polyester elastomer, and ether ester elastomer.

Typical properties

PropertyTypical value
Melting temperature184 °C (ISO 11357-3)
Crystallization temperature110 °C (ISO 11357-3)
Glass transition temperature-65 °C (ISO 11357-2)
Vicat softening, A/5098 °C (ISO 306)
Melt flow index (MFI)20 g/10 min at 220 °C, 2.16 kg (ISO 1133)
Melt volume rate (MVR)18 cm³/10 min at 220 °C, 2.16 kg (ISO 1133)
Shore D hardness29 instantaneous, 26 after 15 s (ISO 868)
Stress at break25 MPa (ISO 527)
Elongation at break700 percent (ISO 527)
Flexural modulus35 MPa (ISO 178)
Notched Izod impact, 23 °CNo break (ISO 180)
Notched Izod impact, -40 °CNo break (ISO 180)
Abrasion resistance35 mm³ at 5 N vertical load (ISO 4649)
Compression set, 23 °C24 percent (ISO 815:1991)
Compression set, 70 °C65 percent (ISO 815:1991)
Density1.09 g/cm³ (ISO 1183)
Water absorption0.8 percent, 24 h immersion at 23 °C (Sipol method MI 08)
ColorNatural; black in the B dry blend
Versions25185 natural, 25185 B black, 25185 W UV stabilized; heat stabilized dry blend on request

Typical values from the manufacturer's technical data sheet. They describe the product, they are not a specification. We will send the current TDS and the batch documentation your qualification needs.

Need this in your system?

Tell us the part or the process, the property you are targeting, and the volume you expect. We will confirm the grade, send the documentation, and get a sample of the candidate grade to you.

Applications

Soft injection molded parts

Shore D 29 with a 35 MPa flexural modulus, molded at 190 to 210 °C barrel temperatures.

Soft extruded profiles and tubing

Extrusion profile of 165 to 180 °C at the feed and 180 to 195 °C at the die.

Food contact parts

The natural grade is stated in compliance with FDA and EU 10/2011 food contact regulations.

UV-exposed parts

The 25185 W dry blend is UV stabilized.

Handling and dispersion

Dry before processing at 90 °C for 2 to 3 hours in a dehumidifying dryer, to a processing moisture content of 0.15 percent.

Suggested injection molding profile for a 184 °C melting grade: rear zone 165 to 180 °C, center zone 190 °C, front zone 200 °C and nozzle 210 °C, with the mold at 20 to 30 °C.

Suggested extrusion profile: feeding zone 165 to 180 °C, compression zone 175 to 185 °C, metering zone 180 to 195 °C and head or die 180 to 195 °C.

Packaging, storage, and regulatory status

Package sizes: 25 kg bags with an aluminum film moisture barrier, 500 kg cardboard octabins with an inner PE liner, and 500 kg and 1000 kg big bags..

Storage: Stable for 12 months unopened in the original packaging, kept cool and dry and protected from light. Material held at around 5 to 10 °C or below should sit at 15 to 20 °C for at least 24 hours before use.

Sipol states the natural grade, with its standard stabilization package, is in compliance with American FDA and European EU 10/2011 food contact regulations. The B and W dry blend data sheets carry no food contact statement. Read the safety data sheet before handling.

Frequently asked questions

What melt temperatures does Sipolprene 25185 need?

Sipolprene 25185 melts at 184 °C. Sipol suggests an injection barrel profile of 165 to 180 °C at the rear zone, 190 °C center, 200 °C front and 210 °C at the nozzle, with the mold at 20 to 30 °C. For extrusion the profile runs 165 to 180 °C at the feed and 180 to 195 °C at the die. Dry at 90 °C for 2 to 3 hours to 0.15 percent moisture first.

Is Sipolprene 25185 food-contact compliant?

The natural Sipolprene 25185, with its standard stabilization package, is stated by Sipol to be in compliance with American FDA and European EU 10/2011 food contact regulations. The statement is on the natural grade's data sheet. The 25185 B black and 25185 W UV-stabilized dry blends carry no food contact statement on their own sheets.

What separates Sipolprene 25185 from Sipolprene 25170?

Sipolprene 25185 melts at 184 °C and softens at 98 °C Vicat, against 173 °C and 73 °C for Sipolprene 25170. Hardness is close, Shore D 29 against 28, but 25185 is stiffer at 35 MPa flexural modulus against 25 MPa and loses less to abrasion, 35 mm³ against 45 mm³. 25170 stretches further, 830 percent against 700 percent.

Which Sipolprene 25185 versions are there?

Sipolprene 25185 has three data sheets with the same Shore D 29 property table. The natural grade carries the FDA and EU 10/2011 statement. 25185 B is the black dry blend and 25185 W is the UV-stabilized dry blend. Sipol makes heat-stabilized dry blends on request; there is no WB data sheet for this grade.

Can I get the TDS and SDS for Sipolprene 25185?

Yes. We send the Technical Data Sheet (TDS), Safety Data Sheet (SDS), and Food contact declaration (FDA, EU 10/2011) on request, in the manufacturer's current revision. Use Request TDS or SDS above and tell us what your qualification review needs.

Related products

Sipolprene 25170

Shore D 28 and softer at 25 MPa flexural modulus, melting at 173 °C.

Sipolprene 35195

Shore D 36 with a 195 °C melting point, the next step up in heat and hardness.

Sipolprene 25150

Shore D 24 at 150 °C, developed for plasticizer-free PVC blends.

Where this grade fits

TPC-ET copolyester elastomers

The Sipolprene range from soft to hard, and where copolyester elastomer fits against TPU.

What is TPC-ET

What the TPC-ET name means and how the family differs from TPU.

Matching a TPC-ET specification

How to match a copolyester elastomer specification by hardness, melt flow and version.

Evaluating Sipolprene 25185?

Tell us the system you are formulating and the property you need to hit. We will confirm the grade, send the data sheet, and ship a sample.