Technipol PA 2170

Low-viscosity copolyamide hot melt, 170 °C softening point, 3.4 Pa·s at 210 °C, Shore D 33 and 600 percent elongation. Applied at 180 to 230 °C.

Home › Products › Sipol › Technipol PA 2170

Technipol PA 2170 is a copolyamide hot-melt adhesive with a softening point of 170 °C and a Brookfield viscosity of 3.4 Pa·s at 210 °C. Sipol characterizes it by its low viscosity at the application temperature, which the data sheet gives as 180 to 230 °C.

The mechanical table describes a soft, very extensible adhesive. Hardness is Shore D 33, falling to 25 after 15 s, elongation at break is 600 percent, stress at break 4.5 MPa and flexural modulus 30 MPa.

The data sheet carries both an extrusion and a melter profile. Sipol states no end use for this grade. The numbers describe a fluid melt and a flexible joint, and the fit for a given job is settled in a trial.

It is also written as copolyamide hot melt adhesive, co-polyamide hot melt, polyamide hot melt adhesive, thermoplastic polyamide adhesive, and CoPA.

Typical properties

PropertyTypical value
Softening point170 °C (Sipol method MI 13)
Brookfield viscosity3.4 Pa·s at 210 °C (Sipol method MI 12, Brookfield CAP 2000+ cone and plate)
Density0.98 g/cm³ (ISO 1183)
Shore D hardness33 instantaneous, 25 after 15 s (ISO 868)
Elongation at break600 percent (ISO 527)
Stress at break4.5 MPa (ISO 527)
Flexural modulus30 MPa (ISO 178)
Indicative application temperature180 to 230 °C
FormGranules

Typical values from the manufacturer's technical data sheet. They describe the product, they are not a specification. We will send the current TDS and the batch documentation your qualification needs.

Need this in your system?

Tell us the part or the process, the property you are targeting, and the volume you expect. We will confirm the grade, send the documentation, and get a sample of the candidate grade to you.

Applications

Low-viscosity hot-melt bonding

Sipol's defining property for PA 2170, 3.4 Pa·s at 210 °C.

Flexible bond lines

Shore D 33 and 600 percent elongation at break for joints that have to flex.

Extruder or melter lines

Sipol publishes a temperature profile for each method.

Handling and dispersion

The indicative application temperature is 180 to 230 °C.

Sipol's suggested extrusion profile: under the hopper 50 to 80 °C, feeding zone 110 to 140 °C, compression zone 150 to 170 °C, metering zone 180 to 200 °C, die or hose 180 to 200 °C, nozzle 190 to 210 °C.

Sipol's suggested melter profile: pre-heating grid 175 to 185 °C, tank 200 to 210 °C, hose 210 to 220 °C, nozzle 210 to 220 °C. Both profiles are starting points for a line trial.

Packaging, storage, and regulatory status

Package sizes: 25 kg bags with an aluminum film moisture barrier, 500 kg cardboard octabins with an inner PE liner, and 500 kg and 1000 kg big bags..

Storage: Stable for 24 months unopened in the original packaging, kept in a cool, dry place and protected from light. Material held at around 5 to 10 °C or below should stand at 15 to 20 °C for at least 24 hours before use.

Read the safety data sheet before handling.

Frequently asked questions

What is Technipol PA 2170 used for?

Sipol's data sheet describes Technipol PA 2170 as a copolyamide hot melt characterized by low viscosity at the application temperature, 3.4 Pa·s at 210 °C, and names no specific end use. Its other numbers, Shore D 33 and 600 percent elongation at break, point to flexible joints. Send the substrates and the application method and we will check the fit with Sipol before a trial.

What application temperature does Technipol PA 2170 need?

Sipol gives an indicative application temperature of 180 to 230 °C for Technipol PA 2170, which softens at 170 °C. The melter profile runs the tank at 200 to 210 °C and the hose and nozzle at 210 to 220 °C. The extrusion profile ends at 190 to 210 °C at the nozzle. Treat both as starting points.

How does Technipol PA 2170 compare with e-Technipol PA 3170?

The data sheets give Technipol PA 2170 and e-Technipol PA 3170 the same 170 °C softening point, 3.4 Pa·s at 210 °C, Shore D 33 and 30 MPa flexural modulus. PA 2170 lists 600 percent elongation at break against 350 percent for e-PA 3170. The e-Technipol grade adds electrical, thermal and water-absorption data and is developed for the electrical and electronics sector.

How does it compare with Technipol PA 2174?

Technipol PA 2170 softens at 170 °C and measures 3.4 Pa·s at 210 °C. Technipol PA 2174 softens at 174 °C and measures 4.0 Pa·s at 205 °C, and Sipol makes it for the automotive filter industry. The two grades share the same extrusion and melter profiles on their data sheets.

Can I get the TDS and SDS for Technipol PA 2170?

Yes. We send the Technical Data Sheet (TDS) and Safety Data Sheet (SDS) on request, in the manufacturer's current revision. Use Request TDS or SDS above and tell us what your qualification review needs.

Related products

e-Technipol PA 3170

Same softening point and viscosity, with electrical data for electronics work.

Technipol PA 2174

Automotive filter grade at 174 °C with the same machine profiles.

Technipol PA 2167

Filter grade at 172 °C and 3.5 Pa·s at 232 °C.

Where this grade fits

Copolyester and copolyamide hot melts

The Technipol and Technipol PA range by softening point and use.

Filter hot melts: a selection guide

Where Sipol's filter copolyamides sit by softening point and viscosity.

Evaluating Technipol PA 2170?

Tell us the system you are formulating and the property you need to hit. We will confirm the grade, send the data sheet, and ship a sample.