Aromatic-aliphatic copolyester (PBAT) certified OK Compost INDUSTRIAL, HOME and SOIL. Melting point 115 °C, Shore D 34. Powder 1160/P and biobased 1164.
Technipol Bio 1160 is an aromatic-aliphatic copolyester, listed by Sipol as PBAT, with medium crystallinity, a melting point of 115 °C and a Shore D hardness of 34. It is certified OK Compost INDUSTRIAL, OK Compost HOME and OK Compost SOIL by TÜV Austria. Sipol formulated it for biodegradable and compostable compounds, and it is usable for injection molding.
Sipol states good compatibility with other biodegradable polymers such as polylactic acid and starch. It works as the support polymer for masterbatches in both granule and powder form. Sipol also states that its Technipol Bio grades comply with both European and US food contact regulations.
It is the soft, tough grade of the certified range. Flexural modulus is 60 MPa, stress at break 17 MPa and elongation at break 365%, and notched Izod gives no break at 23 °C or at -40 °C, with a glass transition at -35 °C.
Technipol Bio 1160/P is the same polymer in powder form, with its particle size distribution measured by ASTM D1921. Its data sheet, an earlier revision, states OK Compost INDUSTRIAL and OK Compost HOME certification. Technipol Bio 1164 carries more than 40% content from inedible-grade renewable sources, on the same property table and with the same three certifications as Bio 1160.
It is also written as PBAT, polybutylene adipate terephthalate, aromatic-aliphatic copolyester, compostable copolyester, biodegradable copolyester, and compostable polyester.
| Property | Typical value |
|---|---|
| Melting temperature | 115 °C (ISO 11357-3) |
| Crystallization temperature | 70 °C (ISO 11357-3) |
| Glass transition temperature | -35 °C (ISO 11357-2) |
| Vicat softening temperature | 69 °C, A/50 (ISO 306) |
| MFI | 20 g/10 min at 160 °C, 2.16 kg (ISO 1133) |
| MVR | 16 cm³/10 min at 160 °C, 2.16 kg (ISO 1133) |
| Shore D hardness | 34 instantaneous, 32 after 15 s (ISO 868) |
| Stress at break | 17 MPa (ISO 527) |
| Elongation at break | 365% (ISO 527) |
| Flexural modulus | 60 MPa (ISO 178) |
| Abrasion resistance | 75 mm³, vertical load 5 N (ISO 4649) |
| Izod impact, notched, 23 °C | No break (ISO 180) |
| Izod impact, notched, -40 °C | No break (ISO 180) |
| Compression set, 23 °C | 34% (ISO 815:1991) |
| Compression set, 70 °C | 48% (ISO 815:1991) |
| Density | 1.23 g/cm³ (ISO 1183) |
| Water absorption | 0.75%, 23 °C for 24 h immersion (Sipol method MI 08) |
| Particle size, 1160/P | 12% at 500 µm or above, 47% at 300 µm, 20% at 250 µm, 21% at 150 µm (ASTM D1921) |
| Certification | OK Compost INDUSTRIAL, HOME and SOIL (TÜV Austria) for 1160 and 1164; 1160/P data sheet states INDUSTRIAL and HOME |
| Renewable content | Bio 1164 above 40% (inedible-grade sources) |
| Form | Granules (1160, 1164); powder (1160/P) |
| Versions | Technipol Bio 1160; Bio 1160/P powder; Bio 1164 |
Typical values from the manufacturer's technical data sheet. They describe the product, they are not a specification. We will send the current TDS and the batch documentation your qualification needs.
Tell us the part or the process, the property you are targeting, and the volume you expect. We will confirm the grade, send the documentation, and get a sample of the candidate grade to you.
Certified OK Compost INDUSTRIAL, HOME and SOIL for compounds that need a soft, tough phase.
Sipol states good compatibility with polylactic acid and starch.
Support polymer in granules, or as the 1160/P powder.
Molded with the nozzle at 120 °C and the mold at 20 to 30 °C.
Bio 1164 carries more than 40% renewable content.
Dry before processing at 60 °C for 2 to 3 hours in a dehumidifying dryer, to a processing moisture content of 0.15%. The same drying applies to the 1160/P powder.
For injection molding, Sipol suggests 105 °C at the rear zone, 110 °C at the center zone, 115 °C at the front zone and 120 °C at the nozzle, with the mold at 20 to 30 °C.
For extrusion, Sipol suggests 95 to 105 °C in the feeding zone, 105 to 125 °C in the compression zone, and 110 to 130 °C in the metering zone and at the head and die. The same profiles apply to Bio 1164.
Package sizes: 25 kg bags with an aluminum film barrier against moisture, 500 kg cardboard octabins with an inner PE liner, and 500 kg and 1000 kg big bags. The same packaging is listed for the 1160/P powder..
Storage: Stable for 6 months unopened in the original packaging, kept in a cool, dry place and protected from light. Material stored at around 5 to 10 °C or below should be held at 15 to 20 °C for at least 24 hours before use.
Technipol Bio 1160 and 1164 are certified OK Compost INDUSTRIAL, OK Compost HOME and OK Compost SOIL by TÜV Austria; the Technipol Bio 1160/P data sheet states OK Compost INDUSTRIAL and HOME. Sipol states that its Technipol Bio grades comply with both European and US food contact regulations. Read the safety data sheet before handling.
Yes. Sipol's current data sheet for Technipol Bio 1160 states certification as OK Compost INDUSTRIAL, OK Compost HOME and OK Compost SOIL by TÜV Austria, and the biobased Bio 1164 states the same three. The data sheet for the 1160/P powder is an earlier revision and states INDUSTRIAL and HOME. Ask for the current certificate with the data sheet; a finished compound needs its own assessment.
Technipol Bio 1160 is Shore D 34 instantaneous and 32 after 15 s, with a flexural modulus of 60 MPa and elongation at break of 365%. Notched Izod gives no break at 23 °C or at -40 °C. Against Technipol Bio 1120, which is Shore D 61 and 450 MPa, it is the grade to blend in where a compostable compound needs flexibility and impact strength.
Technipol Bio 1160/P is the powder form of Technipol Bio 1160, with the same 115 °C melting point and property table. By ASTM D1921, 12% of the powder sits at 500 µm or above, 47% at 300 µm, 20% at 250 µm and 21% at 150 µm. Sipol positions the polymer as a masterbatch support in granules or powder. Dry it at 60 °C for 2 to 3 hours before use.
Technipol Bio 1160 melts at 115 °C. Sipol's injection profile runs 105 °C at the rear zone up to 120 °C at the nozzle, with the mold at 20 to 30 °C. Extrusion runs 95 to 105 °C at the feed up to 110 to 130 °C at the head and die. Its MFI is 20 g/10 min at 160 °C under 2.16 kg.
Yes. We send the Technical Data Sheet (TDS), Safety Data Sheet (SDS), OK Compost certificate, and Food contact declaration (EU and US) on request, in the manufacturer's current revision. Use Request TDS or SDS above and tell us what your qualification review needs.
Stiffer aliphatic certified grade at Shore D 61, with renewable versions to above 95%.
Copolyester PET masterbatch carrier, also made as a powder.
The Technipol Bio range and its certifications.
PET carriers and compostable carriers side by side.