Electronics hot-melt adhesives

e-Technipol PA copolyamide hot melts for low-pressure molding, potting and overmolding. Softening points from 162 to 192 °C, UL94 V-0 grades, adhesion to metals, PVC and polycarbonate.

Home › Products › Electronics hot melts

Copolyamide hot melts for electrical and electronics

e-Technipol PA is Sipol's line of copolyamide hot melts developed for the electrical and electronics sector. The six grades soften between 162 °C and 192 °C, run in melters and in low-pressure molding, potting and overmolding equipment, and bond to metals and to polar plastics such as PVC and polycarbonate. They contain no solvent.

Four of the six carry a UL94 V-0 rating on Sipol's data sheet, and every grade takes more than 60 percent of its raw materials from renewable, non-edible sources. P.A.T. Products supplies the line across the United States, Canada and Mexico.

Choosing among the six grades

Fill thin sections

e-Technipol PA 3168 runs at 0.7 Pa·s at 205 °C, the lowest viscosity in the line, with a UL94 V-0 rating and the highest flexural modulus at 70 MPa.

e-Technipol PA 3168 →

Stay flexible in the cold

e-Technipol PA 3162 holds flexibility to -50 °C and PA 3192 to -45 °C. PA 3170 pairs -40 °C flexibility with 350 percent elongation and the lowest modulus in the line.

e-Technipol PA 3162 →

Run hot

e-Technipol PA 3192 has the highest softening point at 192 °C. PA 3186 has the highest Vicat softening temperature at 70 °C and stretches to 500 percent before break. Both are UL94 V-0.

e-Technipol PA 3192 →

Heat-shrink tubing and sleeves

For the liner inside heat-shrink tubing, Technipol PA 7115 bonds polyethylene and polypropylene and comes through crosslinking and expansion.

Heat-shrink tubing adhesive →

Typical properties side by side

GradeSoftening pointViscosity, Pa·sLow-temperature flexibilityShore DElongationFlexural modulusUL94Renewable content
e-Technipol PA 3162162 °C3.8 at 210 °C-50 °C25250%45 MPanot stated> 61%
e-Technipol PA 3168168 °C0.7 at 205 °C-5 °C37100%70 MPaV-0> 74%
e-Technipol PA 3170170 °C3.4 at 210 °C-40 °C33350%30 MPanot stated> 69%
e-Technipol PA 3186186 °C4.5 at 225 °C-35 °C40500%55 MPaV-0> 75%
e-Technipol PA 3188188 °C2.1 at 210 °C-20 °C35175%40 MPaV-0> 70%
e-Technipol PA 3192192 °C3.1 at 210 °C-45 °C40400%60 MPaV-0> 65%

Typical values from Sipol's technical data sheets: softening point MI 13, Brookfield viscosity MI 12, low-temperature flexibility ASTM D3111, instantaneous Shore D ISO 868, elongation and stress ISO 527, flexural modulus ISO 178, flammability UL94 per IEC 60695-11-10 and -20 as stated on the sheet. Not specification limits.

Moving a part to low-pressure molding?

Tell us the substrates, the operating temperature range and the flammability rating the part needs. We will name the grade and get material to you for a molding trial.

Request a Sample

Thermal data for design

Each e-Technipol PA data sheet also gives the linear thermal expansion between 23 °C and 120 °C, lengthwise and crosswise (ISO 11359), and the thermal conductivity (ASTM E 1461), which runs from 0.151 W/(m·K) on PA 3170 to 0.229 W/(m·K) on PA 3186. Those values are on each grade page.

The grades come in black, and Sipol makes other colors on request. TDS and SDS are available for every grade, with Sipol's REACH and RoHS statements.

Frequently asked questions

What hot melt is used for low-pressure molding of electronics?

Low-pressure molding encapsulates circuit boards, connectors and cable joints in a hot melt injected at low pressure, and copolyamides are the usual chemistry. Sipol's e-Technipol PA grades are copolyamide hot melts developed for that work: they run in low-pressure molding, potting and overmolding equipment, soften between 162 °C and 192 °C, and bond to metals, PVC and polycarbonate.

Which e-Technipol PA grades are rated UL94 V-0?

e-Technipol PA 3168, PA 3186, PA 3188 and PA 3192 each show UL94 V-0 on Sipol's data sheet. The data sheets for PA 3162 and PA 3170 do not state a UL94 rating.

Which grade has the lowest viscosity?

e-Technipol PA 3168, at 0.7 Pa·s Brookfield at 205 °C. Next is PA 3188 at 2.1 Pa·s at 210 °C. Low viscosity fills thin sections and fine features at low injection pressure.

How cold can an e-Technipol PA part go?

Sipol gives low-temperature flexibility by ASTM D3111 on every grade: -50 °C for e-Technipol PA 3162, -45 °C for PA 3192, -40 °C for PA 3170, -35 °C for PA 3186, -20 °C for PA 3188 and -5 °C for PA 3168.

Are these electronics hot melts bio-based?

In part. Each e-Technipol PA grade states its share of raw materials from renewable, non-edible sources: more than 61 percent for PA 3162, rising to more than 75 percent for PA 3186.

Encapsulating a board or connector?

Tell us the substrates, the temperature range and the flammability rating. We will recommend an e-Technipol PA grade and arrange trial material.